Elettronica pratica/Resistori: differenze tra le versioni

Contenuto cancellato Contenuto aggiunto
Nessun oggetto della modifica
Nessun oggetto della modifica
Riga 285:
:<math>\ R = R_0 [1+\alpha(T-T_0)]</math>
 
===Capacità ed induttanza===
 
I resistori reali non solamente evidenziano la proprietà caratterista di resistenza, ma pure una certa capacità e induttanza. Queste proprietà iniziano a diventare importanti se un resistore è impiegato in un qualche circuito ad alta frequenza. I resistori a filo avvolto, per esempio, mostrano una induttanza che li rendono tipicamente inutilizzabili oltre 1kHz.
 
===Montaggio===
===Capacity and Inductance ===
I resistori possono essere modellati in più modi possibili, ma sono ripartiti in resistori a montaggio superficiale, attraverso fori, tramite linguette di saldatura e altre più poche forme. Il fissaggio delle resistenze superficali viene eseguito sullo stesso lato sul quale si trova la resistenza. Nel fissaggio attraverso fori i resistori hanno dei conduttori che passano per il supporto della scheda circuitale e vengono saldati alla scheda sul lato opposto a quello della reistenza, da ciò la denominazione. I resistori con conduttori di collegamento sono pure impiegati nei circuiti punto-a-punto senza scheda circuitale. I resistori ad aggetto hanno degli aggetti per saldarci sopra i fili o connettori per correnti elevate.Comune conformazione dei resistori da montaggio superficiale è quella rettangolare, referenziata da una lunghezza ed una larghezza in mils (centesimi di pollice). Per esempio, un resistore 0805 è un rettangolo da 0,08x0,05 pollici, con contatti su entrambi i lati. I resistori tipici passanti sono cilindrici, referenziati sia da una lunghezza(come 0,300pollici) sia da un tipico limite di potenza che è comune alla lunghezza (un resistore da 1/4 di watt e lungo tipicamente 0,300 pollici). Questa lunghezza non comprende la lunghezza dei conduttori terminali.
 
==Risorse di Wikipedia collegate==
Real world resistors not only show the physical property of resistance, but also have a certain capacity and inductance. These properties start to become important, if a resistor is used in some high frequency circuitry. Wire wound resistors, for example, show an inductance which typically make them unusable above 1kHz.
 
===PackagingLibri===
 
Resistors can be packaged in any way possible, but are divided into surface mount, through hole, soldering tag and a few more forms. Surface mount is connected to the same side that the resistor is on. Through hole resistors have leads (wires) that typically go through the circuit board and are soldered to the board on the side opposite the resistor, hence the name. Resistors with leads are also used in point-to-point circuits without circuit boards. Soldering tag resistors have lugs to solder wires or high current connectors onto.
 
Usual packages for surface mount resistors are rectangular, referenced by a length and a width in mils (thousands of an inch). For instance, an 0805 resistor is a rectangle with length .08" x .05", with contacts (metal that connects to the resistor) on either side. Typical through hole resistors are cylindrical, referenced either by the length (such as 0.300") or by a typical power rating that is common to the length (a 1/4W resistor is typically 0.300"). This length does not include the length of the leads.
 
== Related Wikimedia resources ==
 
=== Wikibooks ===
*[[Circuit Idea]]: [[Circuit Idea/Passive Voltage-to-Current Converter|Passive voltage-to-current converter]] shows how the bare resistor can act as a simple voltage-to-current converter.
 
=== Wikipedia ===
*[[w:Voltage-to-current converter|Voltage-to-current converter]] builds consecutively the passive and active versions of the voltage-to-current converter.<br>
*[[w:Current-to-voltage converter|Current-to-voltage converter]] is dedicated to the passive and active versions of the inverse current-to-voltage converter.
Line 308 ⟶ 303:
[[Categoria:Elettronica pratica|Resistori]]
 
{{avanzamento|25100%|159 febbraiogennaio 20082009}}